View HA12192FHA12197FHA12212FSERIES_2246748.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ha12192f/ha12197f/ha12212f series audio signal processor for car deck (decode only dolby b-type nr with pb amp.) ade-207-167d (z) 5th edition jun. 1999 description ha12192f/ha12197f/ha12212f series are silicon monolithic bipolar ics providing dolby noise reduction system*, music sensor, pb equalizer system in one chip. functions ? pb equalizer 2 channel ? music sensor 1 channel ? decode only dolby b-nr 2 channel note: ha12197f series is not built in dolby b-nr. features ? different type of pb equalizer characteristics selection (120 / 70 position) is available with fully electronic control switching built-in. ? changeable to forward, reverse-mode for pb head with fully electronic control switching built-in. ? available to change music sensing level by external resistor. ? available to change frequency response of music sensor by external capacitor. ? nr on/off fully electronic control switching built-in. (ha12192f/ha12212f series only) ? available to connect direct with mpu. ? ha12192f series, ha12197f series and ha12212f available to allow common pcb designs. ? ha12212f only changes by package from ha12192f series. it is the same electrical characteristics that ha12192f series. * dolby is a trademark of dolby laboratories licensing corporation. a license from dolby laboratories licensing corporation is required for the use of this ic.
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 2 of 89 ordering information function operating voltage product package pb-out level pb-eq dolby b-nr ms min max ha12192f fp-28tb 300mvrms !! ! 6.5v 15v ha12197f ! ! ha12193f 387.5mvrms !! ! 6.8v ha12198f ! ! ha12194f 450mvrms !! ! 7.2v ha12199f ! ! ha12212f fp-40b 300mvrms !! ! 6.5v note: these ics are designed to operate on single supply.
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 3 of 89 pin description and equivalent circuit (v cc = 9v, single supply, ta = 25c, no signal, the value in the table show typical value.) pin no. fp-28tb fp-40b pin name note equivalent circuit description 13 19 msi v = v cc / 2 v 100k v cc /2 ri2 ri1 ha12192/ 3/4 ha12212f ha12197 ha12198 ha12199 ms input * 1 ri1 0 22.6k 33.3k ri2 100k 77.4k 66.7k 18 28 din (l) v = v cc / 2 v 100k v cc /2 deck input 3 3 din (r) 16 * 2 22 det (l) v = 2.5v v cc gnd v time constant pin for rectifier 5 * 2 9det (r) 23 33 rip v = v cc / 2 ripple filter 6 * 2 10 bias v = 0.28v gnd v dolby bias current input note: 1. ms : music sensor 2. non connection regarding ha12197f series.
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 4 of 89 pin description and equivalent circuit (v cc = 9v, single supply, ta = 25c, no signal, the value in the table show typical value.) (cont) pin no. fp-28tb fp-40b pin name note equivalent circuit description 12 18 msdet i = 0 a i gnd time constant pin for rectifier 17 23 pbout (l) v = v cc / 2 v cc gnd v pb output 4 8 pbout (r) 14 20 maout v = v cc / 2 v cc gnd v ms amp. output * 1 26 38 vref reference output 19 29 eqout (l) equalizer output 2 2 eqout (r) (120 ) note: 1. ms : music sensor
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 5 of 89 pin description and equivalent circuit (v cc = 9v, single supply, ta = 25c, no signal, the value in the table show typical value.) (cont) pin no. fp-28tb fp-40b pin name note equivalent circuit description 20 30 m-out (l) v = v cc / 2 v cc gnd v equalizer output (70 ) 11m-out (r) 11 17 v cc v = v cc power supply ? 35, 36 tab v = 0v gnd pin ? 4,5,6,7, 15,16,24, 25,26,27 ? ? nc pin 24 34 fin (l) v = v cc / 2 v equalizer input (forward) 25 37 fin (r) 22 32 rin (l) equalizer input 27 39 rin (r) (reverse) 21 31 nfi (l) negative feedback 28 40 nfi (r) 7 * 1 11 nr off / on i = 20 a i 100k gnd gnd 22k mode control input 8 12 120 / 70 9 13 f / r note: 1. non connection regarding ha12197f series.
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 6 of 89 pin description and equivalent circuit (v cc = 9v, single supply, ta = 25c, no signal, the value in the table show typical value.) (cont) pin no. fp-28tb fp-40b pin name note equivalent circuit description 10 14 msout i = 0 a 100k ms v cc gnd 200 i ms output (to mpu) * 1 15 21 msg v v = v cc / 2 v 90k ms gain terminal * 1 note: 1. ms : music sensor
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 7 of 89 block diagram ha12192f series 10 9 8 7 6 5 4 2 1 28 decode only dolby b-nr 27 26 f 25 r 3 ? + 70 on f/r 120/70 nr off/on 11 12 13 14 15 16 17 19 20 21 22 23 24 18 fr 70 on + tab gnd i.a. i.a. ? + ? decode only dolby b-nr lpf + + det ms d v cc msout micro computer bias det (r) pbout (r) eqout (r) m-out (r) nfi (r) rin (r) v ref fin (r) din (r) v cc msi msg v det (l) pbout (l) eqout (l) m-out (l) nfi (l) rin (l) rip fin (l) din (l) maout msdet ma +
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 8 of 89 ha12197f series 10 9 8 7 6 5 4 2 1 28 27 26 f 25 r 3 ? + 70 on 11 12 13 14 15 16 17 19 20 21 22 23 24 18 fr 70 on + tab gnd i.a. i.a. ? + + lpf + + det ms d v cc msout nc nc pbout (r) eqout (r) m-out (r) nfi (r) rin (r) v ref fin (r) din (r) v cc msi msg v nc pbout (l) eqout (l) m-out (l) nfi (l) rin (l) rip fin (l) din (l) maout msdet ma f/r 120/70 nc ? micro computer
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 9 of 89 ha12212f 14 13 12 11 10 9 8 2 1 40 decode only dolby b-nr 39 38 f 37 r 3 ? + 70 on f/r 120/70 nr off/on 17 18 19 20 21 22 23 29 30 31 32 33 34 28 fr 70 on + i.a. i.a. ? + ? decode only dolby b-nr lpf + + det ms d v cc msout micro computer bias det (r) pbout (r) eqout (r) m-out (r) nfi (r) rin (r) v ref fin (r) din (r) v cc msi msg v det (l) pbout (l) eqout (l) m-out (l) nfi (l) rin (l) rip fin (l) din (l) maout msdet ma + 35 36
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 10 of 89 functional description power supply range ha12192f series and ha12197f series are provided with three line output level, which will permit on optimum overload margin for power supply conditions. and these series are designed to operate on single supply only. table 1 spply voltage range product single supply ha12192f, ha12197f 6.5v to 15.0v ha12193f, ha12198f 6.8v to 15.0v ha12194f, ha12199f 7.2v to 15.0v note: the lower limit of supply voltage depends on the line output reference level. the minimum value of the overload margin is specified as 12db by dolby laboratories. reference voltage these devices provide the reference voltage of half the supply voltage that is the signal grounds. as the peculiarity of these devices, the capacitor for the ripple filter is very small about 1/100 compared with their usual value. the block diagram is shown as figure 1. 11 v cc 23 rip + + ? ? l, r channel eq block l channel dolby block + ? + ? r channel dolby block ms block 26 + c15 1 v ref note: ha12197f series is not built-in dolby block. : internal reference voltage figure 1 the block diagram of reference supply voltage
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 11 of 89 operating mode control ha12192f series and ha12197f series provides fully electronic switching circuits. and each operating mode control are controlled by parallel data (dc voltage). table 2 threshold voltage (v th ) pin no. lo hi unit test condition 7* 1 , 8, 9 ?0.2 to 1.0 3.5 to 5.3 v input pin v measure table 3 switching truth table pin no. lo hi 7* 1 nr-off nr-on 8 120 (normal) 70 (matal or chrome) 9 forward reverse *1. non connection regarding ha12197f series. note: 1. each pins are on pulled down with 100k ? internal resistor. therefore, it will be low-level when each pins are open. 2. over shoot level and under shoot level of input signal must be the standardized. (high: 5.3v, low: ?0.2v) 3. reducing pop noise is so much better for 10k ? to 22k ? resistor and 1 f to 22 f capacitor shown figure 2. input pin 10 to 22k ? mpu + 1 to 22 f figure 2 interface for reduction of pop noise
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 12 of 89 input block diagram and level diagram eq out din input amp. pbout r6 5.1k ? the each level shown above is typical value when offering pbout level to pbout pin. (eq amp. g v = 40db, f=1khz) r5 5.1k ? r4 12k ? r3 18k ? c1 0.01 f m-out nfi rin v ref fin r1 180 ? r2 330k ? + ? + ? 0.6mvrms ( ? 62.2dbs) nr circuit * 1 30mvrms ( ? 28.2dbs) c2 0.1 f note: 1. ha12197f series is not built-in dolby b-nr. pbout level ha12192f/ha12197f : 300mvrms ha12193f/ha12198f : 387.5mvrms ha12194f/ha12199f : 450mvrms ( ? 8.2dbs) ( ? 6.0dbs) ( ? 4.7dbs) eq amp. figure 3 input block diagram adjustment of playback dolby level after replace r5 and r6 with a half-fix volume of 10k ? , adjust playback dolby level.
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 13 of 89 the sensitivity adjustment of music sensor adjusting ms amp. gain by external resistor, the sensitivity of music sensor can set up. the music sensor block diagram is shown in figure 4, and frequency response is shown in figure 5. input amp. micro computer 25khz note: input impedance of msi is 100 k ? typical. ? + din(r) ? din(l) + ? + lpf ma out ms amp. att det msi ms det 90k ? msout gnd r11 330k ? c8 0.01 f c6 0.33 f v cc d v cc r l msg v + ? 6db input amp. + cex2 1 f rex2 2.7k ? rex1 24k ? cex1 0.01 f ser/rep rep mode ser mode i l figure 4 music sensor block diagram f 3 f 4 f 2 f 1 repeat mode search mode (ff or rew) g v2 g v1 10 100 1k 10k 25k 100k f [hz] g v [db] figure 5 frequency response
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 14 of 89 product g v ia att g v ia + att ha12192f series 20db 0db 20db ha12197f 20db 0db 20db ha12198f 22.2db ?2.2db 20db ha12199f 23.5db ?3.5db 20db 1. search mode (ff or rew) g v1 =g v ia + 20log 1 + 90k rex1 + att [db] f 1 = 1 2 cex1 rex1 [hz], f 2 =25k [hz] 2. repeat mode g v2 =g v ia + 20log 1 + 90k z + att [db], z= rex1 rex2 rex1 + rex2 f 3 = 1 2 cex2 rex2 [hz], f 4 =25k [hz] g v ia: input amp. g v = 20db the sensitivity of music sensor (s) is computed by the formula mentioned below. s= ? g v *1 ? 20log 130 *2 30 *3 =12.7 ? g v [db] note: 1. search mode: g v1 , repeat mode: g v2 2. standard level of din pin (dolby level) 3. standard sensing level of music sensor item rex1, 2 cex1, 2 g v1, 2 f 1, 3 f 2, 4 s (one-side channel) search mode 24k ? 0.01 f 33.5db 663hz 25khz ?14.8db repeat mode 2.7k ? 1 f 51.6db 58.9hz 25khz ?33.0db note: s is 6db down in case of one-side channel. and this ms presented hysteresis lest msout terminal should turn over again hi level or lo level, in case of thresh s level constantly.
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 15 of 89 music sensor time constant (1) sensing no signal to signal (attack) is determined by c6. 0.01 f to 1 f capacitor c6 can be applicable. sensing no signal to signal = c6 45000 (sec) (2) sensing signal to no signal (recovery) is determined by c6 and r11, however preceding (1), 100k ? to 1m ? r11 can be applicable. sensing signal to no signal = c6 r11 (sec) music sensor output (msout) as for the internal circuit of music sensor block, music sensor output pin is connected to the collector of npn type directly, therefore, output level will be ?high? when sensing no signal. and output level will be ?low? when sensing signal. connection with microcomputer, design i l at 1ma typ. i l = dv cc ? msout lo * r l *msout lo : sensing signal (about 1v) note: supply voltage of msout pin must be less than v cc voltage. the tolerances of external components for dolby nr-block (only ha12192f series) for adequate dolby nr tracking response, take external components shown below. bias det(r) det(l) c10 0.1 f 10% c4 0.1 f 10% r8 18k ? 2% ha12192f series 16 65 figure 6 tolerance of external components
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 16 of 89 absolute maximum rating (ta=25c) item symbol rating unit note supply voltage v cc max 16 v power dissipation pd 400 mw ta 85c operating temperature topr ?40 to +85 c storage temperature tstg ?55 to +125 c
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 17 of 89 electrical characteristics ha12192f/ha12212f series (ta = 25c, pbout level, 300mvrms(ha12192f/ha12212f), 387.5mvrms (ha12193f), 450mvrms(ha12194f), v cc = 9.0v) item symbol min typ max unit test condition remark quiescent current i q ?9.5?ma nr-on, 70 , no signal imput amp. gain (ha12192f/ha12212f) g v ia 19.0 20.0 21.0 db vin = 0db, f = 1khz imput amp. gain (ha12193f) g v ia 21.2 22.2 23.2 imput amp. gain (ha12194f) g v ia 22.5 23.5 24.5 b-type decode boost dec-2k (1) 2.8 4.3 5.8 db vout = ?20db, f = 2khz dec-2k (2) 7.0 8.5 10.0 vout = ?30db, f = 2khz dec-5k (1) 1.7 3.2 4.7 vout = ?20db, f = 5khz dec-5k (2) 6.7 8.2 9.7 vout = ?30db, f = 5khz signal handling vo max 12.0 13.0 ? db thd = 1%, f = 1khz *1 signal to noise ratio s / n 70.0 80.0 ? db rg = 5.1k ? , ccir / arm thd thd ? 0.05 0.3 % vin = 0db, f = 1khz channel separation ct rl (1) 65 80.0 ? db vin = 10db, f = 1khz din in ct rl (2) 50 60.0 ? eq in pb-eq gain g v eq 1k 37.0 40.0 43.0 db vin = 0.6mvrms, f = 1khz 120 g v eq 10k(1) 33.0 36.0 39.0 vin = 0.6mvrms, f = 10khz g v eq 10k(2) 29.0 32.0 35.0 70 pb-eq maximum output vom 300 600 ? mvrms thd = 1%, f = 1khz *1 pb-eq thd thd-eq ? 0.05 0.3 % vin = 0.6mvrms, f = 1khz noise voltage level converted in input v n ?0.71.5 vrms rg = 680 ? , din-audio ms sensing level v on ?18.0 ?14.0 ?10.0 db f = 5khz ms output low level v ol ?1.01.5v ms output leak current i oh ?0.02.0 a control voltage v il ?0.2 ? 1.0 v v ih 3.5 ? 5.3 note: 1. v cc = 6.5v (ha12192f/ha12212f) v cc = 6.8v (ha12193f) v cc = 7.2v (ha12194f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 18 of 89 electrical characteristics ha12197f series (ta = 25c, pbout level, 300mvrms(ha12197f), 387.5mvrms(ha12198f), 450mvrms(ha12199f), v cc = 9.0v) item symbol min typ max unit test condition remark quiescent current i q ?4.77.1ma 70 , no signal imput amp. gain (ha12197f) g v ia 19.0 20.0 21.0 db vin = 0db, f = 1khz imput amp. gain (ha12198f) g v ia 21.2 22.2 23.2 imput amp. gain (ha12199f) g v ia 22.5 23.5 24.5 signal handling vo max 12.0 13.0 ? db thd = 1%, f = 1khz *1 signal to noise ratio s / n 70.0 80.0 ? db rg = 5.1k ? , ccir / arm thd thd ? 0.05 0.3 % vin = 0db, f = 1khz channel separation ct rl (1) 65 80.0 ? db vin = 10db, f = 1khz din in ct rl (2) 50 60.0 ? eq in pb-eq gain g v eq 1k 37.0 40.0 43.0 db vin = 0.6mvrms, f = 1khz 120 g v eq 10k(1) 33.0 36.0 39.0 vin = 0.6mvrms, f = 10khz g v eq 10k(2) 29.0 32.0 35.0 70 pb-eq maximum output vom 300 600 ? mvrms thd = 1%, f = 1khz *1 pb-eq thd thd-eq ? 0.05 0.3 % vin = 0.6mvrms, f = 1khz noise voltage level converted in input v n ?0.71.5 vrms rg = 680 ? , din-audio ms sensing level v on ?18.0 ?14.0 ?10.0 db f = 5khz ms output low level v ol ?1.01.5v ms output leak current i oh ?0.02.0 a control voltage v il ?0.2 ? 1.0 v v ih 3.5 ? 5.3 note: 1. v cc = 6.5v (ha12197f) v cc = 6.8v (ha12198f) v cc = 7.2v (ha12199f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 19 of 89 test circuit ha12192f/ha12197f series r3 18k r4 12k c2 0.1 r5 5.1k r6 5.1k c1 0.01 r2 330k r1 180 + 28 27 22 1 2 3 456 16 15 8 9 10 11 12 13 14 c19 0.47 r24 10k + c3 2.2 r8 18k c4 0.1 r7 10k pb eq pb eq sw9 sw6 r23 680 r22 680 + c18 22 + c17 22 24 + c14 22 r20 680 + + c16 22 c15 1 tab d f r f d r ac vm1 audio sg r l sw4 sw2 sw1 off on sw3 21 20 19 18 r19 180 c13 0.01 r18 330k r25 10k c12 0.1 r15 5.1k r14 5.1k + c20 0.47 r17 18k r16 12k r12 24k c10 0.1 + c11 2.2 r13 10k tab d d c9 0.01 pb eq pb eq sw5 sw8 + 7 c5 22 r9 22k tab r10 3.9k r f 70 120 on off r11 330k + c6 0.33 + c7 100 c8 0.01 ms r l sw10 dc source3 dc source2 dc source1 dc vm 5v 9v l r sw7 ac vm2 noise meter distortion analyzer oscillo scope ha12192f/ha12197f series fp-28tb nfi(r) rin(r) v ref fin(r) rip rin(l) fin(l) nfi(l) din(r) eqout(r) m-out(r) bias det(r) pbout(r) din(l) eqout(l) m-out(l) msg v det(l) pbout(l) noise meter with ccir/arm filter and din-audio filter note: 1. 2. 3. resistor tolerance 1% capacitor tolerance 1% unit r: ? c: f 23 17 r21 680 26 25 tab nr off/on 120/70 f/r msout msdet msi v cc maout
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 20 of 89 ha12212f r3 18k r4 12k c2 0.1 r5 5.1k r6 5.1k c1 0.01 r2 330k r1 180 + 40 39 32 1 2 38910 22 21 12 13 14 17 18 19 20 c19 0.47 r24 10k + c3 2.2 r8 18k c4 0.1 r7 10k pb eq pb eq sw9 sw6 r23 680 r22 680 + c18 22 + c17 22 34 + c14 22 r20 680 + + c16 22 c15 1 d f r f d r ac vm1 audio sg r l sw4 sw2 sw1 off on sw3 31 30 29 28 r19 180 c13 0.01 r18 330k r25 10k c12 0.1 r15 5.1k r14 5.1k + c20 0.47 r17 18k r16 12k r12 24k + c11 2.2 r13 10k d d c9 0.01 pb eq pb eq sw5 sw8 + 11 c5 22 r9 22k r10 3.9k r f 70 120 on off r11 330k + c6 0.33 + c7 100 c8 0.01 ms r l sw10 dc source3 dc source2 dc source1 dc vm 5v 9v l r sw7 ac vm2 noise meter distortion analyzer oscillo scope ha12212f fp-40b nfi(r) rin(r) v ref fin(r) rip rin(l) fin(l) nfi(l) din(r) eqout(r) m-out(r) bias det(r) pbout(r) din(l) eqout(l) m-out(l) msg v det(l) pbout(l) noise meter with ccir/arm filter and din-audio filter 33 23 r21 680 38 37 nr off/on 120/70 f/r msout msdet msi v cc maout 35 gnd 36 gnd 16 15 nc nc 4 5 6 7 nc nc nc nc nc nc nc nc 27 26 25 24 note: 1. 2. 3. resistor tolerance 1% capacitor tolerance 1% unit r: ? c: f
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 21 of 89 characteristic curves ha12192f series 6 8 10 12 14 16 10 9 8 7 nr-off (120/ ) nr-off (70/ ) nr-on (120/ ) nr-on (70/ ) no-signal 26 22 18 14 10 6 10 100 1 k 10 k 100 k 1 m v cc = 9 v din pbout (nr-off) supply voltage (v) quiescent current vs. supply voltage (ha12192f/3f/4f) quiescent current i cc (ma) frequency (hz) input amp gain vs. frequency (ha12192f) gain (db)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 22 of 89 din pbout, nr-off v cc = 9 v 10 100 1 k 10 k 100 k 1 m 26 22 18 14 10 6 din pbout, nr-off v cc = 9 v 10 100 1 k 10 k 100 k 1 m 26 22 18 14 10 6 gain (db) frequency (hz) gain (db) frequency (hz) din input amp. gain vs. frequency (ha12193f) din input amp. gain vs. frequency (ha12194f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 23 of 89 0 ?2 ?4 ?6 ?8 ?10 ?12 ?14 100 200 500 1 k 2 k 5 k 10 k 20 k v cc = 6.5 v, 9 v 15 v ?40 db ?30 db ?20 db ?10 db 0 db vout din pbout 0 ?2 ?4 ?6 ?8 ?10 ?12 ?14 100 200 500 1 k 2 k 5 k 10 k 20 k v cc = 6.8 v, 9 v 15 v ?40 db ?30 db ?20 db ?10 db 0 db vout din pbout decode cut (db) frequency (hz) decode cut vs. frequency (ha12192f) decode cut (db) frequency (hz) decode cut vs. frequency (ha12193f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 24 of 89 0 ? 2 ? 4 ? 6 ? 8 ? 10 ? 12 ? 14 v cc = 7.2 v, 9v 15 v din pbout 100 200 500 1 k 2 k 5 k 10 k 20 k ? 40 db ? 30 db ? 20 db ? 10 db 0 db vout 25 20 15 10 6 8 10 12 14 16 nr-off nr-on f = 1 khz 0 db = 300 mvrms t.h.d. = 1.0% din pbout decode cut (db) frequency (hz) decode cut vs. frequency (ha12194f) supply voltage (v) maximum output level vomax (db) maximum output level vs. supply voltage (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 25 of 89 25 20 15 10 6 8 10 12 14 16 nr-off nr-on f = 1 khz 0 db = 387.5 mvrms t.h.d. = 1.0% din pbout nr-off nr-on 6 8 10 12 14 16 25 20 15 10 f = 1 khz vout = 450 mvrms t.h.d = 1.0 % din pbout supply voltage (v) maximum output level vomax (db) maximum output level vs. supply voltage (ha12193f) supply voltage (v) maximum output level vomax (db) maximum output level vs. supply voltage (ha12194f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 26 of 89 85 80 75 70 6 8 10 12 14 16 nr-off nr-on din pbout ccir/arm s = 300 mvrms 85 80 75 70 6 8 10 12 14 16 nr-off nr-on din pbout ccir/arm s = 387.5 mvrms supply voltage (v) signal to noise ratio s/n (db) signal to noise ratio vs. supply voltage (ha12192f) supply voltage (v) signal to noise ratio s/n (db) signal to noise ratio vs. supply voltage (ha12193f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 27 of 89 6 8 10 12 14 16 70 75 80 85 ccir/arm s = 450 mvrms nr-off nr-on din pbout 1.0 0.1 0.01 6 8 10 12 14 16 f = 100 hz f = 1 khz f = 10 khz din pbout nr-off vout = 300 mvrms supply voltage (v) signal to noise ratio s/n (db) signal to noise ratio vs. supply voltage (ha12194f) supply voltage (v) total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (1) (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 28 of 89 1.0 0.1 0.01 6 8 10 12 14 16 din pbout nr-on vout = 300 mvrms f = 100 hz f = 1 khz f = 10 khz 6 8 10 12 14 16 1.0 0.1 0.01 din pbout nr-off vout = 387.5 mvrms f = 100 hz f = 1 khz f = 10 khz supply voltage (v) total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (2) (ha12192f) supply voltage (v) total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (1) (ha12193f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 29 of 89 6 8 10 12 14 16 1.0 0.1 0.01 din pbout nr-on vout = 387.5 mvrms f = 100 hz f = 1 khz f = 10 khz 6 8 10 12 14 16 1.0 0.1 0.01 din pbout nr-off vout = 450 mvrms f = 100 hz f = 1 khz f = 10 khz supply voltage (v) total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (2) (ha12193f) supply voltage (v) total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (1) (ha12194f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 30 of 89 6 8 10 12 14 16 1.0 0.1 0.01 din pbout nr-on vout = 450 mvrms f = 100 hz f = 1 khz f = 10 khz 5.0 0.1 0.01 ? 10 0 10 15 20 v cc = 9 v din pbout vout = 300 mvrms = 0 db nr-off f = 100 hz f = 1 khz f = 10 khz ? 55 0.02 0.05 0.2 0.5 1.0 2.0 supply voltage (v) total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (2) (ha12194f) output level vout (db) total harmonic distortion t.h.d. (%) total harmonic distortion vs. output level (1) (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 31 of 89 5.0 0.1 0.01 ? 10 0 10 15 20 f = 100 hz f = 1 khz f = 10 khz ? 55 0.02 0.05 0.2 0.5 1.0 2.0 v cc = 9 v din pbout vout = 300 mvrms = 0 db nr-on ? 10 ? 50 510 20 0.01 0.05 5 f = 100 hz f = 1 khz f = 10 khz v cc = 9 v din pbout vout = 387.5 mvrms = 0 db nr-off 0.1 2 1.0 0.5 0.2 0.02 15 output level vout (db) total harmonic distortion t.h.d. (%) total harmonic distortion vs. output level (2) (ha12192f) output level vout (db) total harmonic distortion t.h.d. (%) total harmonic distortion vs. output level (1) (ha12193f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 32 of 89 ? 10 ? 50 510 20 0.01 0.05 f = 100 hz f = 1 khz f = 10 khz 0.1 1.0 0.5 0.2 0.02 15 v cc = 9 v din pbout vout = 387.5 mvrms = 0 db nr-on 2 5 ? 10 ? 50 510 20 0.01 0.05 5 f = 100 hz f = 1 khz f = 10 khz v cc = 9 v din pbout vout = 450 mvrms = 0 db nr-off 0.1 2 1.0 0.5 0.2 0.02 15 output level vout (db) total harmonic distortion t.h.d. (%) total harmonic distortion vs. output level (2) (ha12193f) output level vout (db) total harmonic distortion t.h.d. (%) total harmonic distortion vs. output level (1) (ha12194f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 33 of 89 ? 10 ? 50 510 20 0.01 0.05 f = 100 hz f = 1 khz f = 10 khz 0.1 1.0 0.5 0.2 0.02 15 v cc = 9 v din pbout vout = 450 mvrms = 0 db nr-on 2 5 0.5 0.01 100 +10 db 0 db ? 10 db nr-off din pbout v cc = 9 v 0 db = 300 mvrms 500 1 k 5 k 10 k 0.1 0.05 400 hz hpf + 80 khz lpf 30 khz lpf hpf : high pass filter lpf : low pass filter 400 hz hpf+30 khz lpf 20 k output level vout (db) total harmonic distortion t.h.d. (%) total harmonic distortion vs. output level (2) (ha12194f) frequency (hz) total harmonic distortion t.h.d. (%) total harmonic distortion vs. frequency (1) (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 34 of 89 0.5 0.01 100 +10 db 0 db ? 10 db nr-on din pbout v cc = 9 v 0 db = 300 mvrms 500 1 k 5 k 10 k 0.1 0.05 400 hz hpf + 80 khz lpf 400 hz hpf+30 khz lpf 30 khz lpf hpf : high pass filter lpf : low pass filter 20 k 0.5 0.01 100 +10 db 0 db ? 10 db nr-off din pbout v cc = 9 v 0 db = 387.5 mvrms 500 1 k 5 k 10 k 0.1 0.05 400 hz hpf + 80 khz lpf 30 khz lpf hpf : high pass filter lpf : low pass filter 400 hz hpf+30 khz lpf 20 k frequency (hz) total harmonic distortion t.h.d. (%) total harmonic distortion vs. frequency (2) (ha12192f) frequency (hz) total harmonic distortion t.h.d. (%) total harmonic distortion vs. frequency (1) (ha12193f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 35 of 89 0.5 0.01 100 +10 db 0 db ? 10 db nr-on din pbout v cc = 9 v 0 db = 387.5 mvrms 500 1 k 5 k 10 k 0.1 0.05 400 hz hpf + 80 khz lpf 400 hz hpf+30 khz lpf 30 khz lpf hpf : high pass filter lpf : low pass filter 20 k 0.5 0.01 100 +10 db 0 db ? 10 db nr-off din pbout v cc = 9 v 0 db = 450 mvrms 500 1 k 5 k 10 k 0.1 0.05 400 hz hpf + 80 khz lpf 30 khz lpf hpf : high pass filter lpf : low pass filter 400 hz hpf+30 khz lpf 20 k frequency (hz) total harmonic distortion t.h.d. (%) total harmonic distortion vs. frequency (2) (ha12193f) frequency (hz) total harmonic distortion t.h.d. (%) total harmonic distortion vs. frequency (1) (ha12194f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 36 of 89 0.5 0.01 100 +10 db 0 db ? 10 db nr-on din pbout v cc = 9 v 0 db = 450 mvrms 500 1 k 5 k 10 k 0.1 0.5 400 hz hpf + 80 khz lpf 30 khz lpf hpf : high pass filter lpf : low pass filter 400 hz hpf+30 khz lpf 20 k 0 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 20 k frequency (hz) total harmonic distortion t.h.d. (%) total harmonic distortion vs. frequency (2) (ha12194f) frequency (hz) channel separation (db) channel separation vs. frequency (l r) din pbout (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 37 of 89 0 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 20 k frequency (hz) channel separation (db) channel separation vs. frequency (r l) din pbout (ha12192f) frequency (hz) channel separation (db) channel separation vs. frequency (l r) din pbout (ha12193f) 0 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 38 of 89 0 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 20 k ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 0 20 k frequency (hz) channel separation (db) channel separation vs. frequency (r l) din pbout (ha12193f) frequency (hz) channel separation (db) channel separation vs. frequency (l r) din pbout (ha12194f) nr-off nr-on v cc = 9 v
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 39 of 89 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 0 20 k 0 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 20 k frequency (hz) channel separation (db) channel separation vs. frequency (r l) din pbout (ha12194f) channel separation vs. frequency (l r) fin pbout (ha12192f) frequency (hz) channel separation (db)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 40 of 89 0 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 20 k 0 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 20 k channel separation vs. frequency (r l) fin pbout (ha12192f) frequency (hz) channel separation (db) channel separation vs. frequency (l r) fin pbout (ha12193f) frequency (hz) channel separation (db)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 41 of 89 0 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 20 k ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 0 20 k channel separation vs. frequency (r l) fin pbout (ha12193f) frequency (hz) channel separation (db) channel separation vs. frequency (l r) eqfin pbout (ha12194f) frequency (hz) channel separation (db)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 42 of 89 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v 0 20 k ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v ? 120 20 k channel separation vs. frequency (r l) eqfin pbout (ha12194f) frequency (hz) channel separation (db) frequency (hz) crosstalk (db) crosstalk vs. frequency (forward reverse) pbout (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 43 of 89 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 v cc = 9 v 20 k nr-off nr-on ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 nr-off nr-on v cc = 9 v ? 120 ? 120 20 k frequency (hz) crosstalk (db) crosstalk vs. frequency (forward reverse) pbout (ha12193f) frequency (hz) crosstalk (db) crosstalk vs. frequency (reverse forward) pbout (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 44 of 89 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 v cc = 9 v 20 k nr-off nr-on ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 v cc = 9 v 20 k ? 120 ? 120 nr-off nr-on frequency (hz) crosstalk (db) crosstalk vs. frequency (forward reverse) pbout (ha12194f) frequency (hz) crosstalk (db) crosstalk vs. frequency (reverse forward) pbout (ha12193f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 45 of 89 ? 100 20 40 100 400 1 k 4 k 10 k ? 80 ? 60 ? 40 ? 20 v cc = 9 v ? 120 20 k nr-off nr-on ? 60 20 40 100 400 1 k 4 k 10 k ? 50 ? 40 ? 30 ? 20 pbout nr-on eqout v cc = 9 v ? 70 pbout nr-off 20 k frequency (hz) crosstalk (db) crosstalk vs. frequency (reverse forward) pbout (ha12194f) frequency (hz) ripple rejection ratio r.r.r. (db) ripple rejection ratio vs. frequency (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 46 of 89 ? 60 20 40 100 400 1 k 4 k 10 k ? 50 ? 40 ? 30 ? 20 pbout nr-on eqout v cc = 9 v ? 70 pbout nr-off 20 k ? 60 20 40 100 400 1 k 4 k 10 k ? 50 ? 40 ? 30 ? 20 pbout nr-on eqout v cc = 9 v pbout nr-off ? 70 20 k frequency (hz) ripple rejection ratio r.r.r. (db) ripple rejection ratio vs. frequency (ha12193f) frequency (hz) ripple rejection ratio r.r.r. (db) ripple rejection ratio vs. frequency (ha12194f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 47 of 89 60 55 50 45 6 8 10 12 14 16 eqin pbout s = 300 mvrms din audio nr-off 120 nr-off 70 nr-on 120 nr-on 70 60 55 50 45 6 8 10 12 14 16 eqin pbout s = 387.5 mvrms din audio nr-off 120 nr-off 70 nr-on 120 nr-on 70 supply voltage (v) signal to noise ratio s/n (db) signal to noise ratio vs. supply voltage (ha12193f) supply voltage (v) signal to noise ratio s/n (db) signal to noise ratio vs. supply voltage (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 48 of 89 6 8 10 12 14 16 45 50 55 60 nr-off 120 nr-off 70 nr-on 120 nr-on 70 eqin pbout s = 450 mvrms din-audio 1.0 0.01 10 5 0 5 10 15 nr-off 120 nr-off 70 nr-on 120 nr-on 70 v cc = 9 v eqin pbout f = 1 khz 0 db = 300 mvrms 0.1 20 5 supply voltage (v) signal to noise ratio s/n (db) signal to noise ratio vs. supply voltage (ha12194f) output level vout (db) total harmonic distortion t.h.d. (%) total harmonic distortion vs. output level (ha12192f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 49 of 89 1.0 0.01 ? 10 ? 5051015 nr-off 120 nr-off 70 nr-on 120 nr-on 70 v cc = 9 v eqin pbout f = 1 khz 0 db = 387.5 mvrms 0.1 20 5 ? 10 ? 50 51015 0.01 0.1 1.0 5 nr-off 120 nr-off 70 nr-on 120 nr-on 70 v cc = 9 v eqin pbout f = 1 khz 0 db = 450 mvrms 20 output level vout (db) total harmonic distortion t.h.d. (%) total harmonic distortion vs. output level (ha12194f) output level vout (db) total harmonic distortion t.h.d. (%) total harmonic distortion vs. output level (ha12193f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 50 of 89 1.0 0.1 0.01 6 8 10 12 14 16 nr-off 120 nr-off 70 nr-on 120 nr-on 70 eqin pbout f = 1 khz vout = +10 db 0.5 0.05 1.0 0.1 0.01 6 8 10 12 14 16 nr-off 120 nr-off 70 nr-on 120 nr-on 70 eqin pbout f = 1 khz vout = +10 db 0.5 0.05 supply voltage (v) total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (ha12192f) supply voltage (v) total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (ha12193f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 51 of 89 6 8 10 12 14 16 0.01 0.05 1.0 nr-off 120 nr-off 70 nr-on 120 nr-on 70 eqin pbout f = 1 khz vout = +10 db 0.1 0.5 70 50 20 20 40 100 400 1 k 40 4 k 10 k 40 k 100 k 30 60 v cc = 9 v 120 70 supply voltage (v) total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (ha12194f) frequency (hz) gain (db) eq amp. gain vs. frequency (ha12192f/3f/4f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 52 of 89 6 5 4 3 2 1 0 6 8 10 12 14 16 eqin eqout f = 1 khz t.h.d = 1.0 % 120 70 40 32 24 16 8 0 20 40 100 400 1 k 4 k 10 k 40 k 100 k v cc = 9 v maout msi supply voltage (v) maximum output voltage vomax (vrms) maximum output voltage vs. supply voltage (ha12192f/3f/4f) gain (db) frequency (hz) ms-amp gain vs. frequency (ha12192f/3f/4f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 53 of 89 5 0 ? 10 ? 5 ? 15 10 100 1 k 10 k 100 k msout v cc = 9 v din 1 channel input v cc = 9 v f = 5 khz din msout 0 db ? 10 db pbout msout msdet v cc r 11 0.33 f c 6 + 50 k 100 k 500 k 1 m 500 100 50 10 5 10 k frequency (hz) ms sensing level (db) ms sensing vs. frequency (ha12192f/3f/4f) resistance r 11 ( ? ) signal sensing time (ms) signal sensing time vs. resistance (ha12192f/3f/4f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 54 of 89 vout = 0 db vout = ? 10 db v cc = 9 v f = 5 khz din msout 0 db = pbout = 450 mvrms pbout msout v cc msdet c 6 + 330 k ? 50 10 5.0 1.0 0.5 0.01 0.05 0.1 0.5 1 capacitance c 6 ( f) signal sensing time vs. capacitance (ha12192f/3f/4f) signal sensing time (ms)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 55 of 89 ? ha12197f series no-signal 120 70 68 10 12 14 16 15 10 5 0 supply voltage (v) quiescent current i cc (ma) quiescent current vs. supply voltage (ha12199f/8f/7f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 56 of 89 10 100 1 k 10 k 100 k frequency (hz) 26 22 18 14 10 6 gain (db) input amp. gain vs. frequency (ha12197f) v cc = 9 v din pbout v cc = 9 v din pbout 10 100 1 k 10 k 100 k 26 22 18 14 10 6 frequency (hz) gain (db) input amp. gain vs. frequency (ha12198f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 57 of 89 10 100 1 k 10 k 100 k 26 22 18 14 10 6 gain (db) din pbout v cc = 9 v frequency (hz) input amp. gain vs. frequency (ha12199f) 6 8 10 12 14 16 25 20 15 supply voltage (v) maximum output level vomax (db) maximum output level vs. supply voltage (ha12197f) 10 t.h.d. = 1% f = 1 khz din pbout = 300 mvrms = 0 db
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 58 of 89 maximum output level vomax (db) supply voltage (v) 6 8 10 12 14 16 25 20 15 10 maximum output level vs. supply voltage (ha12198f) t.h.d. = 1 % f = 1 khz din pbout = 387.5 mvrms = 0 db 6 8 10 12 14 16 25 20 15 10 supply voltage (v) maximum output level vomax (db) maximum output level vs. supply voltage (ha12199f) din pbout = 450 mvrms = 0 db t.h.d. = 1 % f = 1 khz
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 59 of 89 din pbout = 300 mvrms = 0 db ccir/arm 6 8 10 12 14 16 supply voltage (v) signal to noise ratio s/n (db) 85 80 75 70 signal to noise ratio vs. supply voltage (ha12197f) din pbout = 387.5 mvrms = 0 db ccir/arm 6 8 10 12 14 16 supply voltage (v) signal to noise ratio s/n (db) 85 80 75 70 signal to noise ratio vs. supply voltage (ha12198f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 60 of 89 din pbout = 450 mvrms = 0 db ccir/arm 6 8 10 12 14 16 85 80 75 70 supply voltage (v) signal to noise ratio s/n (db) signal to noise ratio vs. supply voltage (ha12199f) 10 khz (400 hz hpf + 80 khz lpf) 1 khz (400 hz hpf + 30 khz lpf) 100 hz (30 khz lpf) din pbout 6 8 10 12 14 16 supply voltage (v) 0.1 0.01 0.001 total harmonic distortion t.h.d. (%) total harmonic distortion vs. supply voltage (ha12197f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 61 of 89 10 khz (400 hz hpf + 80 khz lpf) 1 khz (400 hz hpf + 30 khz lpf) 100 hz (30 khz lpf) din pbout 0.1 0.01 0.001 total harmonic distortion t.h.d. (%) 6 8 10 12 14 16 supply voltage (v) total harmonic distortion vs. supply voltage (ha12198f) 6 8 10 12 14 16 supply voltage (v) 0.1 0.01 0.001 total harmonic distortion t.h.d. (%) 10 khz (400 hz hpf + 80 khz lpf) 1k hz (400 hz hpf + 30 khz lpf) 100 hz (30 khz lpf) din pbout total harmonic distortion vs. supply voltage (ha12199f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 62 of 89 100 hz (30 khz lpf) 1 khz (400 hz hpf + 30 khz lpf) 10 khz (400 hz hpf + 80 khz lpf) din pbout = 300 mvrms = 0 db v cc = 9 v total harmonic distortion t.h.d. (%) ? 15 ? 10 ? 50 5101520 output level vout (db) 0.1 5 1.0 0.01 total harmonic distortion vs. output level (ha12197f) v cc = 9 v 100 hz (30 khz lpf) 1k hz (400 hz hpf + 30 khz lpf) 10 khz (400 hz hpf + 80 khz lpf) din pbout = 387.5 mvrms = 0 db total harmonic distortion t.h.d. (%) 5 1.0 0.1 0.01 ? 15 ? 10 ? 50 5101520 output level vout (db) total harmonic distortion vs. output level (ha12198f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 63 of 89 100 hz (30 khz lpf) 1 khz (400 hz hpf + 30 khz lpf) 10 khz (400 hz hpf + 80 khz lpf) din pbout = 450 mvrms = 0 db v cc = 9 v ? 15 ? 10 ? 50 5101520 5 1.0 0.1 0.01 total harmonic distortion t.h.d. (%) output level vout (db) total harmonic distortion vs. output level (ha12199f) 30 khz lpf 400 hz hpf + 30 khz lpf 400 hz hpf + 80 khz lpf 100 500 1 k 5 k 10 k frequency (hz) 0.5 0.1 0.05 0.01 total harmonic distortion t.h.d. (%) total harmonic distortion vs. frequency (ha12197f) +10 db 0 db ? 10 db din pbout v cc = 9 v
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 64 of 89 100 500 1 k 5 k 10 k frequency (hz) 0.5 0.1 0.05 0.01 total harmonic distortion t.h.d. (%) total harmonic distortion vs. frequency (ha12198f) +10 db 0 db ? 10 db din pbout 30 khz lpf 400 hz hpf + 30 khz lpf 400 hz hpf + 80 khz lpf v cc = 9 v din pbout +10 db 0 db ? 10 db 30 khz lpf 400 hz hpf + 30 khz lpf 400 hz hpf + 80 khz lpf 100 500 1 k 5 k 10 k 0.5 0.1 0.05 0.01 total harmonic distortion t.h.d. (%) frequency (hz) total harmonic distortion vs. frequency (ha12199f) v cc = 9 v
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 65 of 89 ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (l r) din pbout (ha12197f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 0 v cc = 9 v 20 k ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (r l) din pbout (ha12197f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 0 v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 66 of 89 ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (l r) din pbout (ha12198f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 0 v cc = 9 v 20 k ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (r l) din pbout (ha12198f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 0 v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 67 of 89 0 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (l r) din pbout (ha12199f) 4 k 10 k ? 100 ? 80 ? 60 ? 40 ? 20 v cc = 9 v 20 k 0 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (r l) din pbout (ha12199f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 ? 100 v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 68 of 89 ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (l r) fin pbout (ha12197f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 120 0 70 v cc = 9 v 20 k ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (r l) fin pbout (ha12197f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 120 0 70 v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 69 of 89 ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (l r) fin pbout (ha12198f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 120 0 70 v cc = 9 v 20 k ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (r l) fin pbout (ha12198f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 120 0 70 v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 70 of 89 ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (l r) fin pbout (ha12199f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 120 ? 10 70 v cc = 9 v 20 k ? 100 20 40 100 400 1 k frequency (hz) channel separation (db) channel separation vs. frequency (r l) fin pbout (ha12199f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 120 ? 10 70 v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 71 of 89 ? 100 20 40 100 400 1 k frequency (hz) crosstalk (db) crosstalk vs. frequency (forward reverse) pbout (ha12197f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 ? 10 120 70 v cc = 9 v 20 k ? 100 20 40 100 400 1 k frequency (hz) crosstalk (db) crosstalk vs. frequency (reverse forward) pbout (ha12197f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 ? 10 120 70 v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 72 of 89 ? 100 20 40 100 400 1 k frequency (hz) crosstalk (db) crosstalk vs. frequency (forward reverse) pbout (ha12198f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 ? 10 120 70 v cc = 9 v 20 k ? 100 20 40 100 400 1 k frequency (hz) crosstalk (db) crosstalk vs. frequency (reverse forward) pbout (ha12198f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 ? 10 120 70 v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 73 of 89 ? 100 20 40 100 400 1 k frequency (hz) crosstalk (db) crosstalk vs. frequency (forward reverse) pbout (ha12199f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 ? 10 120 70 v cc = 9 v 20 k ? 100 20 40 100 400 1 k frequency (hz) crosstalk (db) crosstalk vs. frequency (reverse forward) pbout (ha12199f) 4 k 10 k ? 80 ? 60 ? 40 ? 20 ? 10 120 70 v cc = 9 v 20 k
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 74 of 89 ? 70 20 40 100 400 1 k frequency (hz) ripple rejection ratio r.r.r. (db) ripple rejection ratio vs. frequency (ha12197f) 4 k 10 k ? 50 ? 40 ? 30 v cc = 9 v ? 20 eqout pbout ? 60 ? 70 20 40 100 400 1 k frequency (hz) ripple rejection ratio r.r.r. (db) ripple rejection ratio vs. frequency (ha12198f) 4 k 10 k ? 50 ? 40 ? 30 v cc = 9 v ? 20 eqout pbout ? 60
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 75 of 89 ? 70 20 40 100 400 1 k frequency (hz) ripple rejection ratio r.r.r. (db) ripple rejection ratio vs. frequency (ha12199f) 4 k 10 k ? 50 ? 40 ? 30 v cc = 9 v ? 20 eqout pbout ? 60 65 60 55 50 6 8 10 12 14 16 supply voltage (v) signal to noise ratio vs. supply voltage (ha12197f) signal to noise ratio s/n (db) eqin pbout s = 300 mvrms din-audio f 120 r 120 f 70 r 70
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 76 of 89 65 60 55 50 6 8 10 12 14 16 supply voltage (v) signal to noise ratio vs. supply voltage (ha12198f) signal to noise ratio s/n (db) eqin pbout s = 387.5 mvrms din-audio f 120 r 120 f 70 r 70 65 60 55 50 6 8 10 12 14 16 supply voltage (v) signal to noise ratio vs. supply voltage (ha12199f) signal to noise ratio s/n (db) eqin pbout s = 450 mvrms din-audio f 120 r 120 f 70 r 70
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 77 of 89 total harmonic distortion vs. output level (ha12197f) total harmonic distortion t.h.d. (%) 5.0 1.0 0.1 ? 20 ? 10 0 10 20 output level vout (db) v cc = 9 v eqin pbout = 300 mvrms = 0 db f = 1 khz (400 hz hpf + 30 khz lpf) 120 70 total harmonic distortion vs. output level (ha12198f) total harmonic distortion t.h.d. (%) 5.0 1.0 0.1 ? 20 ? 10 0 10 20 output level vout (db) v cc = 9 v eqin pbout = 387.5 mvrms = 0 db f = 1 khz (400 hz hpf + 30 khz lpf) 120 70
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 78 of 89 total harmonic distortion vs. output level (ha12199f) total harmonic distortion t.h.d. (%) 5.0 1.0 0.1 ? 20 ? 10 0 10 20 output level vout (db) v cc = 9 v eqin pbout = 450 mvrms = 0 db f = 1 khz (400 hz hpf + 30 khz lpf) 120 70 total harmonic distortion vs. supply voltage (1) (ha12197f) total harmonic distortion t.h.d. (%) 0.5 6 supply voltage (v) 0.1 0.01 8 10121416 fin pbout f 120 vout = +10 db : 100 hz (30 khz lpf) : 1 khz (400 hz hpf + 30 khz lpf) : 10 khz (400 hz hpf + 80 khz lpf)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 79 of 89 total harmonic distortion vs. supply voltage (2) (ha12197f) total harmonic distortion t.h.d. (%) 0.5 6 supply voltage (v) 0.1 0.01 8 10121416 fin pbout f 70 vout = +10 db : 100 hz (30 khz lpf) : 1 khz (400 hz hpf + 30 khz lpf) : 10 khz (400 hz hpf + 80 khz lpf) total harmonic distortion vs. supply voltage (1) (ha12198f) total harmonic distortion t.h.d. (%) 0.5 6 supply voltage (v) 0.1 0.01 8 10121416 fin pbout f 120 vout = +10 db : 100 hz (30 khz lpf) : 1 khz (400 hz hpf + 30 khz lpf) : 10 khz (400 hz hpf + 80 khz lpf)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 80 of 89 total harmonic distortion vs. supply voltage (2) (ha12198f) total harmonic distortion t.h.d. (%) 0.5 6 supply voltage (v) 0.1 0.01 8 10121416 fin pbout f 70 vout = +10 db : 100 hz (30 khz lpf) : 1 khz (400 hz hpf + 30 khz lpf) : 10 khz (400 hz hpf + 80 khz lpf) total harmonic distortion vs. supply voltage (1) (ha12199f) total harmonic distortion t.h.d. (%) 0.5 6 supply voltage (v) 0.1 0.01 8 10121416 eqin pbout f 120 vout = +10 db : 100 hz (30 khz lpf) : 1 khz (400 hz hpf + 30 khz lpf) : 10 khz (400 hz hpf + 80 khz lpf)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 81 of 89 total harmonic distortion vs. supply voltage (2) (ha12199f) total harmonic distortion t.h.d. (%) 0.5 6 supply voltage (v) 0.1 0.01 8 10121416 fin pbout f 70 vout = +10 db : 100 hz (30 khz lpf) : 1 khz (400 hz hpf + 30 khz lpf) : 10 khz (400 hz hpf + 80 khz lpf) 70 60 50 40 30 20 20 40 100 400 1 k 4 k 10 k 40 k 100 k frequency (hz) gain (db) eq-amp. gain vs. frequency (ha12197f/8f/9f) 120 70 v cc = 9 v
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 82 of 89 6 5 4 3 2 1 0 6 8 10 12 14 16 supply voltage (v) maximum output level vomax (vrms) maximum output level vs. supply voltage (ha12197f/8f/9f) eqin eqout t.h.d. = 1 % f = 1 khz : 120 : 70 34 20 frequency (hz) gain (db) ms-amp. gain vs. frequency (ha12197f) 28 22 16 10 4 40 100 400 1 k 4 k 10 k 40 k 100 k v cc = 9 v maout msi
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 83 of 89 34 20 frequency (hz) gain (db) ms-amp. gain vs. frequency (ha12198f) 28 22 16 10 4 40 100 400 1 k 4 k 10 k 40 k 100 k msi maout v cc = 9 v 34 20 frequency (hz) gain (db) ms-amp. gain vs. frequency (ha12199f) 28 22 16 10 4 40 100 400 1 k 4 k 10 k 40 k 100 k maout msi v cc = 9 v
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 84 of 89 10 10 100 1 k 10 k 100 k frequency (hz) ms sensing level (db) ms sensing level vs. frequency (ha12197f) 5 0 ? 5 ? 10 ? 15 v cc = 9 v din 1 channel input 5 v 0 v 0 v 5 v v cc = 9 v din 1 channel input 5 v 0 v 0 v 5 v 10 10 100 1 k 10 k 100 k frequency (hz) ms sensing level (db) ms sensing level vs. frequency (ha12198f) 5 0 ? 5 ? 10 ? 15
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 85 of 89 10 10 100 1k 10k 100k frequency (hz) ms sensing level (db) ms sensing level vs. frequency (ha12199f) 5 0 ? 5 ? 10 ? 15 v cc = 9 v din 1 channel input 5 v 0 v 0 v 5 v
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 86 of 89 sensing time (ms) 500 100 50 10 5 2 10 k 50 k 100 k 500 k 1m pbout msout resistance r11 ( ? ) sensing time vs. resistance (ha12197f/8f/9f) v cc = 9 v, c6 = 0.33 f f = 5 khz din pbout msout : 0 db : ? 5db = 300 mvrms = 0 db (ha12197f) = 387.5 mvrms = 0 db (ha12198f) = 450 mvrms = 0 db (ha12199f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 87 of 89 50 10 5.0 1.0 0.5 0.2 0.01 0.05 0.1 0.5 1.0 capacitance c6 ( f) signal sensing time vs. capacitance (ha12197f/8f/9f) signal sensing time (ms) pbout msout v cc = 9 v, r11 = 330 k ? f = 5 khz msout din pbout : 0 db : ? 5 db : ? 10 db = 300 mvrms = 0 db (ha12197f) = 387.5 mvrms = 0 db (ha12198f) = 450 mvrms = 0 db (ha12199f)
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 88 of 89 package dimensions hitachi code jedec eiaj weight (reference value) fp-28tb ? ? 0.2 g unit: mm *dimension including the plating thickness base material dimension 9.0 ?0.2 7.0 *0.32 ?0.08 0.13 20 15 1 6 21 28 14 7 0.65 9.0 ?0.2 0.10 1.0 0? ?8? 0.50 ?0.10 *0.17 ?0.05 1.70 max m 2.25 ?0.10 0.95 ?0.10 0.575 0.575 + 0.09 ?0.05 0.13 1.40 0.15 ?0.04 0.30 ?0.06 hitachi code jedec eiaj weight (reference value) fp-40b conforms 0.2 g unit: mm *dimension including the plating thickness base material dimension 9.0 0.2 7.0 *0.25 0.05 0.13 30 21 110 31 40 20 11 0.65 9.0 0.2 0.10 0 ? 8 ? 0.50 0.10 *0.17 0.05 1.70 max m 1.0 0.22 0.04 1.40 + 0.09 0.05 0.13 0.15 0.04 0.575 0.575
ha12192f/ha12197f/ha12212f series rev.5, jun. 1999, page 89 of 89 disclaimer 1. hitachi neither warrants nor grants licenses of any rights of hitachi?s or any third party?s patent, copyright, trademark, or other intellectual property rights for information contained in this document. hitachi bears no responsibility for problems that may arise with third party?s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. products and product specifications may be subject to change without notice. confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. hitachi makes every attempt to ensure that its products are of high quality and reliability. however, contact hitachi?s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. design your application so that the product is used within the ranges guaranteed by hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail- safes, so that the equipment incorporating hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the hitachi product. 5. this product is not designed to be radiation resistant. 6. no one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from hitachi. 7. contact hitachi?s sales office for any questions regarding this document or hitachi semiconductor products. sales offices hitachi, ltd. semiconductor & integrated circuits. nippon bldg., 2-6-2, ohte-machi, chiyoda-ku, tokyo 100-0004, japan tel: tokyo (03) 3270-2111 fax: (03) 3270-5109 copyright ? hitachi, ltd., 2000. all rights reserved. printed in japan. hitachi asia ltd. hitachi tower 16 collyer quay #20-00, singapore 049318 tel : <65>-538-6533/538-8577 fax : <65>-538-6933/538-3877 url : http://www.hitachi.com.sg url northamerica : http://semiconductor.hitachi.com/ europe : http://www.hitachi-eu.com/hel/ecg asia : http://sicapac.hitachi-asia.com japan : http://www.hitachi.co.jp/sicd/indx.htm hitachi asia ltd. (taipei branch office) 4/f, no. 167, tun hwa north road, hung-kuo building, taipei (105), taiwan tel : <886>-(2)-2718-3666 fax : <886>-(2)-2718-8180 telex : 23222 has-tp url : http://www.hitachi.com.tw hitachi asia (hong kong) ltd. group iii (electronic components) 7/f., north tower, world finance centre, harbour city, canton road tsim sha tsui, kowloon, hong kong tel : <852>-(2)-735-9218 fax : <852>-(2)-730-0281 url : http://www.hitachi.com.hk hitachi europe ltd. electronic components group. whitebrook park lower cookham road maidenhead berkshire sl6 8ya, united kingdom tel: <44> (1628) 585000 fax: <44> (1628) 585160 hitachi europe gmbh electronic components group dornacher stra e 3 d-85622 feldkirchen, munich germany tel: <49> (89) 9 9180-0 fax: <49> (89) 9 29 30 00 hitachi semiconductor (america) inc. 179 east tasman drive, san jose,ca 95134 tel: <1> (408) 433-1990 fax: <1>(408) 433-0223 for further information write to: colophon 2.0

▲Up To Search▲

Price & Availability of HA12192FHA12197FHA12212FSERIES

	To Download HA12192FHA12197FHA12212FSERIES Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .